Skip to main content

Installing PVDM into Cisco 2811

In order to install a PVDM into the Cisco 2800 series simply follow the steps below.

Firstly power down the router and remove the case by undoing the case screws.
At the back of the router near the power supply you will notice the memory (DIMM Slots) and behind them the PVDM slots (which are white).
If you look closely on the mother board you will notice that one is labeled PVDM0 and the other PVDM1.

If you are only installing one PVDM then you will need to install it in the PVDM0 slot.
The PVDM has a little notch cut out of it which means it will only fit into the slot one way.  Locate the PVDM into the slot at a slight angle and then tip pull it upright until the clips click into place and hold it in position.



Put the case back onto the router and switch it on.  Once booted do a show inventory and you should now see the PVDM listed.

Comments

Post a Comment

Popular posts from this blog

Error Message %DUAL-6-NBRINFO: EIGRP-IPv4 34256

If you see the error  %DUAL-6-NBRINFO: EIGRP-IPv4 xxxx  is blocked: not on common subnet then it simply means that there are EIGRP devices sending multicast hellos on an interface which have a different IP Range configured to the receiving router.  160617: .Feb 22 15:11:05.194 GMT: %DUAL-6-NBRINFO: EIGRP-IPv4 34256: Neighbor 17 2.31.253.1 (Vlan43) is blocked: not on common subnet                                                     (172.31.252.1/31) 160618: .Feb 22 15:11:12.770 GMT: %DUAL-6-NBRINFO: EIGRP-IPv4 34256: Neighbor 19 2.168.205.0 (Vlan44) is blocked: not on common subnet (192.168.204.1/31)                                                                                          This is most likely to occur by accident when two subnets are configured on the same VLAN, with EIGRP running on the interface.
Post a Comment
Read more

Moving the SSH port on a CISCO router

If you admin your routers over the internet you probably know you should be using SSH. Telnet being sent in clear text is easily sniffed and your passwords captured. However Cisco routers use the standard TCP port 22 for their SSH service. As soon as you open this up to the world and turn on SSH access logging you will start to see hundreds of IP's connecting to your device and running dictionary attacks against you using standard username and password combinations. The majority of these IP's seem to originate from China or Russia and they find your open port extremely quickly. This is very anoying it fills up your log files with these attacks and uses up your system resources dealing with them. I believe they are simply running scans for any open TCP port 22. For this reason I decided I could cut down the amount of attacks by moving the SSH port to a different number. One thing you should know before we start is that there is no way to actually change the SSH port number o
Post a Comment
Read more

Shutting Cisco 3750 Stackwise ports

Today I came across a customers 3750 switch stack which had a flapping stackwise link. The stackwise link was transitioning up/down around 3 times a second and causing massive issues with connectivity and EIGRP routing for the site. Previously I believed that I would need to physically remove the Stackwise cable in order to restore service by shutting the flapping link. It seems it is possible to shut the Stackwise port from the CLI although it is done from enable mode rather than Configure terminal. The command is.. Switch#switch 1 stack port 1 ? disable Disable stack port enable Enable stack port The first number 1 would indicate the switch number in the stack and the second number 1 after the port is the Stackwise port number you want to shut. Make a note of which switch and port you shut as it will not show up in the config or the show outputs which could prove tricky when you want to reenable it.. You can determine the status of the ports using the command below but not how
Post a Comment
Read more